Docooler JINGSHA X99-8D3 Motherboard User Manual

1. Introdução e maisview

The Docooler JINGSHA X99-8D3 is a high-performance ATX gaming motherboard designed for LGA2011 V3 processors. It features four-channel DDR3 memory support, an M.2 NVME slot for high-speed storage, and multiple PCI-E expansion slots, making it suitable for demanding computing tasks and gaming setups. This manual will guide you through the installation, configuration, and maintenance of your motherboard.

Figura 1.1: Visão de cima para baixo view of the Docooler JINGSHA X99-8D3 Motherboard, showcasing its layout with CPU socket, RAM slots, and various expansion slots.

2. Principais características

• M.2 NVME Support: Equipped with an M.2 hard disk port, supporting high-speed PCI-E NVME X4 for optimal operating system and application driver performance.
• Quad-Channel DDR3 Memory: Features 8 DDR3 memory slots across 4 channels, significantly improving capacity and performance, supporting up to 256GB.
• Digital Diagnostic Card: Integrated digital diagnostic card automatically tests hardware devices to ensure proper operation and assist in troubleshooting.
• Multiple PCI-E Expansion Slots: Provides 3 PCI-E expanded slots, configurable as X16/X8 to handle various workloads and multi-GPU setups.
• Construção durável: Built with a 10-layer PCB and high-quality capacitors for enhanced stability and heat resistance.

Figure 2.1: Diagram illustrating the six core technologies and features of the motherboard, including 4-channel DDR3*8, M.2 hard disk interface, digital diagnostic card, 7.1 channel audio, SATA3.0*8 interface, and Crossfire support.

3. Conteúdo da embalagem

Por favor, verifique se todos os itens listados abaixo estão presentes em sua embalagem:

• 1x Docooler JINGSHA X99-8D3 Motherboard
• 1x Cabo SATA
• 1x I/O Baffle (Backplate)
• 1x CPU Fan Board
• A bag of screws

4. Especificações

Figura 4.1: Detalhado view of the motherboard's rear I/O panel, showing PS/2 ports, USB 2.0, USB 3.0, Gigabit Network Port, and 7.1 Audio Ports.

5. Configuração e instalação

Antes de iniciar a instalação, certifique-se de que o sistema esteja desligado e desconectado da tomada. Manuseie a placa-mãe pelas bordas para evitar descargas eletrostáticas.

5.1 Instalando a CPU

1. Locate the LGA2011 V3 CPU socket on the motherboard.
2. Gently push down the CPU retention lever and swing it open.
3. Align the triangular mark on your CPU with the corresponding mark on the socket. Carefully place the CPU into the socket without forcing it.
4. Feche a alavanca de retenção para fixar a CPU.
5. Aplique uma camada fina e uniforme de pasta térmica na parte superior do processador.
6. Install the CPU cooler according to its manufacturer's instructions, ensuring proper contact and pressure.

Figura 5.1: Close view of the LGA2011 V3 CPU socket on the motherboard, ready for CPU installation.

5.2 Installing RAM Modules

1. Abra as travas em ambas as extremidades dos slots de memória DDR3.
2. Align the notch on the RAM module with the key in the memory slot.
3. Pressione firmemente ambas as extremidades do módulo de RAM até que as presilhas se encaixem no lugar, fixando o módulo.
4. For optimal performance, install RAM modules in matching pairs across the four channels as indicated in the motherboard manual or silkscreen.

Figura 5.2: View of the eight DDR3 RAM slots on the motherboard, showing their arrangement for quad-channel memory configuration.

5.3 Installing Storage Devices (M.2 NVME & SATA)

1. SSD M.2 NVMe: Localize o slot M.2. Insira o SSD M.2 em um ângulo no slot, pressione-o suavemente para baixo e fixe-o com o parafuso fornecido.
2. Unidades SATA: Connect your SATA SSDs or HDDs to the SATA 3.0 ports using SATA data cables. Ensure the power supply SATA power connectors are also attached to the drives.

Figure 5.3: Close-up of the M.2 interface on the motherboard, highlighting its position and the PCI-E Gen3 X4 connection for high-speed data transfer.

Figura 5.4: View of the eight orange SATA 3.0 ports on the motherboard, providing ample connectivity for storage devices.

5.4 Conectando a fonte de alimentação

1. Connect the 24-pin ATX power connector from your power supply unit (PSU) to the corresponding port on the motherboard.
2. Connect the 8-pin CPU power connector (EPS12V) from your PSU to the 8-pin port near the CPU socket.

5.5 Installing Expansion Cards (PCIe)

1. Locate the desired PCI-E 3.0 x16 or x1 slots.
2. Remova a tampa do slot de expansão correspondente do gabinete do seu PC.
3. Align the expansion card with the slot and press down firmly until it is fully seated. Secure the card with a screw to the case.

Figura 5.5: Angulado view of the motherboard, highlighting the three PCI Express 3.0 x16 slots and the smaller PCIe x1 slots, ready for graphics cards and other expansion cards.

6. Operando a placa-mãe

6.1 Primeira inicialização e configuração da BIOS

1. Após montar todos os componentes, conecte o monitor, o teclado e o mouse.
2. Power on your system. During the initial boot sequence, repeatedly press the DEL or F2 key (common for JINGSHA motherboards) to enter the BIOS/UEFI setup utility.
3. In the BIOS, verify that all installed components (CPU, RAM, storage) are detected correctly.
4. Configure a ordem de inicialização para priorizar a mídia de instalação do seu sistema operacional (unidade USB ou DVD).
5. Save changes and exit BIOS. The system will restart.

6.2 Instalação do Sistema Operacional

Follow the instructions provided with your operating system (e.g., Windows, Linux) to complete the installation process. Ensure you install all necessary drivers for the motherboard's chipsets, network, audio, and other components from the manufacturer's website or included driver disc.

7. Manutenção

A manutenção adequada garante a longevidade e o funcionamento estável da sua placa-mãe.

• Remoção de poeira: Limpe regularmente a poeira da placa-mãe e dos componentes usando ar comprimido. Certifique-se de que o sistema esteja desligado e desconectado da tomada antes de realizar a limpeza.
• Atualizações da BIOS: Periodically check the Docooler or JINGSHA official website for BIOS updates. BIOS updates can improve compatibility, stability, and performance. Follow update instructions carefully to avoid damaging the motherboard.
• Atualizações de Driver: Mantenha os drivers do sistema atualizados para garantir o melhor desempenho e a compatibilidade com novos softwares e hardwares.
• Condições ambientais: Operate the motherboard in a well-ventilated environment with stable temperature and humidity to prevent overheating and component degradation.

8. Solução De Problemas

Esta seção aborda problemas comuns que você pode encontrar.

8.1 Sem energia / Sem inicialização

• Ensure the 24-pin ATX and 8-pin CPU power connectors are securely plugged into the motherboard.
• Check if the power supply unit (PSU) is switched on and connected to a working power outlet.
• Verify that the front panel power button cable is correctly connected to the motherboard's header.

8.2 Sem saída de vídeo

• Ensure your graphics card (if dedicated) is properly seated in its PCI-E slot and has all necessary power cables connected.
• Check that your monitor cable is securely connected to the graphics card or motherboard (if integrated graphics are used, though X99 typically requires a dedicated GPU).
• Try reseating your RAM modules. Incorrectly seated RAM is a common cause of no display.

8.3 POST Code Display (Digital Diagnostic Card)

The motherboard is equipped with a digital diagnostic card (POST code display) that shows a two-digit code during boot-up. Refer to the motherboard's detailed technical documentation (often available on the manufacturer's website) for a list of POST codes and their meanings. This can help pinpoint the exact component causing a boot failure.

Figura 8.1: Close view showing the integrated digital diagnostic card (POST code display) on the motherboard, which assists in identifying hardware issues during boot.

9. Garantia e Suporte

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Docooler or JINGSHA website. Guarde o comprovante de compra para solicitações de garantia.