Introdução
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Lnicez 850GPH Submersible Pump. Please read this manual thoroughly before use and retain it for future reference.
Instruções de segurança
- Always disconnect the power supply before handling, installing, or performing maintenance on the pump.
- Ensure the power outlet is properly grounded and protected by a Ground Fault Circuit Interrupter (GFCI).
- Não utilize a bomba se o cabo de alimentação ou a ficha estiverem danificados.
- Do not run the pump dry. The built-in temperature control core will automatically cut off power if it runs dry to prevent burnout, but prolonged dry running should be avoided.
- The pump is designed for water temperatures between 32℉ (0℃) and 95℉ (35℃). Do not use with liquids outside this range.
- Mantenha crianças e animais de estimação afastados da bomba durante o funcionamento.
- This pump is intended for pumping clean water. Avoid pumping flammable, corrosive, or abrasive liquids.
Conteúdo da embalagem
Ao abrir a embalagem, verifique se todos os itens estão presentes e sem danos:
- 1 x Lnicez 850GPH Submersible Pump (Model: LLW199)
- 3 x Detachable Adapters (3/4'', 3/5'', 1/2'')
- 1 x Manual de Instruções
Image: The Lnicez 850GPH Submersible Pump shown with its three included detachable adapters (3/4'', 3/5'', 1/2'').
Configuração e instalação
- Choose the Right Adapter: Select the appropriate detachable adapter (3/4'', 3/5'', or 1/2'') that matches your water pipe or hose.
- Conecte o adaptador: Securely screw the chosen adapter onto the pump's outlet.
- Conecte a mangueira: Connect your water hose to the attached adapter. Ensure a tight connection to prevent leaks.
- Posicione a bomba: Place the pump in the water source you intend to drain. Ensure the pump is fully submerged for optimal performance and to prevent dry running. The minimum water level for operation is 0.4 inches.
- Conexão de energia: Plug the 16.5ft power cord into a grounded 110V/60HZ AC outlet.
Image: Diagram illustrating the dimensions of the Lnicez submersible pump (12cm width, 13cm height) and the three different hose adapter sizes (3/4", 3/5", 1/2").
Instruções de operação
Once the pump is set up and connected, operation is straightforward:
- Iniciar bombeamento: The pump will begin operating as soon as it is plugged into a live electrical outlet.
- Monitorar o nível da água: Ensure the water level remains above the minimum 0.4-inch mark for continuous operation. The pump is designed to drain water down to a very low level.
- Desligamento automático: The pump features a built-in constant temperature core that will automatically cut off power if it detects dry running or overheating, protecting the motor from damage.
- Aplicações: This pump is suitable for various applications including draining swimming pools, pool covers, fish ponds, puddles, and for use in hydroponic systems or statuary.
- To Stop Operation: Simply unplug the pump from the power outlet.
Imagem: Visual examples of the pump's wide application, including draining a swimming pool, watering a garden, circulating water in a fish pond, and removing water from a puddle.
Image: Illustration demonstrating the pump's high-speed effluent time (30L in 1 minute) and its ability to operate down to a minimum water level of 0.4 inches.
Manutenção e Limpeza
Regular cleaning ensures optimal performance and extends the lifespan of your pump. Always unplug the pump before cleaning.
- Remove Water Filter Cover: Use a screwdriver to pry open the four snap points on the bottom of the pump to remove the water filter cover.
- Remove Water Leaf Cover: After removing the water filter cover, you will see a black snap-on water leaf cover. Use a screwdriver to remove it. Be careful not to break the point on the cover when taking it off.
- Remove Pump's Rotor: Once the water leaf cover is off, you will see the rotor, which consists of a magnet and a plastic impeller, a stainless steel shaft core, and two black silicone bushings. Carefully take these components out separately.
- Limpeza eficaz: Use detergent to assist in cleaning visible stains and impurities. Pay special attention to cleaning the pump rotor catch and the water outlet.
- Reinstalação: After cleaning, follow these steps to reassemble the pump:
- Install the rotor. Ensure the two black silicone bushings are aligned with their respective holes.
- Install the water lobe cover and fix its location.
- Instale a tampa do filtro de água.
- A instalação está concluída.
Image: Diagram illustrating the internal components of the pump, highlighting the Temperature Control Core for safety and the Upgraded Copper Motor for enhanced performance.
Solução de problemas
If you encounter issues with your Lnicez pump, refer to the following common problems and solutions:
| Problema | Possível causa | Solução |
|---|---|---|
| A bomba não liga. | No power, loose connection, or tripped GFCI. | Check power outlet, ensure plug is fully inserted, reset GFCI. |
| Pump runs but no water is flowing or flow is weak. | Pump not fully submerged, clogged intake/outlet, airlock, or damaged impeller. | Ensure pump is submerged. Disconnect power and check for blockages in intake and outlet. Clean impeller area as per maintenance instructions. |
| A bomba para inesperadamente. | Overheating (dry running), power interruption, or internal fault. | Check water level; if low, the temperature control core may have activated. Allow pump to cool down before restarting. Verify power supply. |
| A bomba está excessivamente barulhenta. | Debris in impeller, pump not stable, or worn components. | Disconnect power and clean impeller. Ensure pump is placed on a stable, flat surface. |
Especificações
| Recurso | Detalhe |
|---|---|
| Marca | Lnicez |
| Número do modelo | LLW199 |
| Fonte de energia | Elétrico com fio |
| Volumetage | 110V/60HZ AC |
| O quetage | 75 W (1/10 HP) |
| Taxa de fluxo máxima | 850 GPH (galões por hora) |
| Cabeça Máxima | 10.5 pés |
| Comprimento do cabo de alimentação | 16.5 pés |
| Nível Mínimo de Água | 0.4 polegadas |
| Temperatura mínima da água | 32℉ (0℃) |
| Temperatura máxima da água | 95℉ (35℃) |
| Material | Acrilonitrila Butadieno Estireno (ABS) |
| Peso | 1.9 libras |
| Certificações | CE, FCC, UL, EMC |
Image: Display of the professional certifications obtained by the Lnicez pump, including CE, FCC, UL, and EMC, ensuring safety and quality.
Garantia e Suporte
For warranty information, technical support, or any inquiries regarding your Lnicez 850GPH Submersible Pump, please contact the manufacturer or seller directly. You can often find contact details on the product packaging or through the official Lnicez store on Amazon: