iFlight 5.8Ghz 40CH 2.5W/ 4.9Ghz 8CH 2.5W 2-8S VTX BWhoop

1. Produto acabadoview

Descrição

The iFlight BLITZ Whoop VTX is a high-power video transmitter designed for FPV drones and quadcopters. It features a built-in microphone, multiple power levels up to 2500mW, and supports 2-8S VBAT input. The VTX includes an integrated cooling fan and CNC cooling casing for efficient heat dissipation. It utilizes an MMCX interface and has a 25.5x25.5mm mounting pattern. Control is managed via LED indicators and function buttons for power level, band, and channel selection, with IRC Tramp telemetry support.

Principais características

• Built-in microphone for audio transmission.
• Vol de entradatage range: 7V to 34V (2-8S VBAT).
• Four selectable power levels: PIT/25mW/400mW/1000mW/2500mW.
• 8 channels for 4.9Ghz and 40 channels for 5.8Ghz operation.
• CNC cooling casing with integrated cooling fan for dual heat dissipation.
• MMCX antenna interface.
• Compact dimensions: 50*30*16 mm, Lightweight: 32g.
• VTX telemetry: IRC Tramp.

O que está na caixa

• 1 x BLITZ Whoop 4.9G 2.5W VTX
• Necessary wiring harnesses
• Parafusos de montagem

Figure 1.1: The iFlight BLITZ Whoop VTX module with its antenna cable, mounting screws, and wiring harnesses.

2. Informações importantes de segurança

AVISO: The VTX is set to 25mW by default. Power levels above 25mW require a HAM license or must be approved by local authorities. Always ensure you are flying legal frequencies and use the appropriate Betaflight VTX tables according to your region's regulations.

• Always read the instructions for proper wiring before connecting the VTX. Incorrect wiring can cause damage.
• Ensure the antenna is properly installed before powering on the VTX. Operating without an antenna can significantly shorten the module's lifespan.
• Verifique o volume corretotage range (7-34V DC) and polarity (positive/negative) before applying power to prevent component damage.
• When installing the VTX, ensure sufficient space around the module for air convection to facilitate proper heat dissipation.
• Failure to provide adequate cooling may cause the module to activate overheat protection, leading to reduced power transmission or complete shutdown.

3. Guia de configuração

Wiring and Port Connections

The BLITZ Whoop VTX features clearly labeled ports for easy integration into your FPV system. Refer to the diagram below for correct connections.

Figura 3.1: parte inferior view of the VTX showing port connections.

Montagem

The VTX has a mounting pattern of 25.5x25.5mm with Φ1.6mm holes. Ensure secure mounting using the provided screws. It is crucial to leave adequate space around the VTX for air circulation to allow the integrated cooling fan and CNC casing to dissipate heat effectively. This prevents the VTX from entering overheat protection mode.

4. Instruções de operação

Funcionalidade do botão liga/desliga

The VTX features a 'Power' button to control its output power and PIT mode. Refer to the image below for button location.

Figura 4.1: Lateral view of the VTX showing the 'Band/CH' and 'Power' buttons.

• Pressione e segure por 2 segundos: Enters or exits PIT mode. A solid green LED light indicates that PIT mode is active.
• Pressão curta: Changes the output power level. The number of green LED flashes indicates the current power setting:
  
  • 1 flash = 25mW
  • 2 flashes = 400mW
  • 3 flashes = 1000mW
  • 4 flashes = 2500mW

Band and Channel Button Functionality

The 'Band/CH' button allows you to cycle through the available bands and channels. Refer to Figure 4.1 for button location.

• Pressão curta: Switches the channel. The number of blue LED flashes indicates the current channel (1 to 8 for 4.9Ghz, or 1 to 40 for 5.8Ghz depending on the selected band).

VTX Telemetry (IRC Tramp)

The BLITZ Whoop VTX supports IRC Tramp telemetry, allowing you to configure VTX settings directly from your flight controller's OSD (On-Screen Display) or Betaflight configurator. Connect the IRC pin on the VTX to a UART TX pad on your flight controller and configure the UART for VTX (Tramp) protocol in Betaflight.

5. Especificações técnicas

6. Manutenção

To ensure the longevity and optimal performance of your iFlight BLITZ Whoop VTX, follow these maintenance guidelines:

• Mantenha limpo: Regularly inspect the VTX for dust, dirt, or debris, especially around the cooling fan and heatsink fins. Use a soft brush or compressed air to gently clean these areas.
• Garanta o resfriamento adequado: Always ensure that the VTX has adequate airflow during operation. Avoid enclosing it in tight spaces without ventilation, as this can lead to overheating and performance degradation.
• Conexão da antena: Periodically check the MMCX antenna connection to ensure it is secure. A loose connection can lead to poor video quality and potential damage to the VTX.
• Inspecionar a fiação: Before each flight, visually inspect all wiring connected to the VTX for any signs of wear, fraying, or damage. Replace any damaged wires immediately.

7. Solução De Problemas

This section addresses common issues you might encounter with your iFlight BLITZ Whoop VTX.

8. Garantia e Suporte

For warranty information, please refer to the official iFlight website or contact your point of purchase. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase.

For technical support, troubleshooting assistance beyond this manual, or to inquire about spare parts, please visit the official iFlight support channels or their Amazon store page:

Visit the iFlight Store on Amazon

Please have your product model number (BLITZ Whoop VTX) and purchase details ready when contacting support.

9. Vídeos oficiais do produto

No official product videos from the seller were provided for this manual. Please check the product listing or the manufacturer's official website para quaisquer recursos de vídeo disponíveis.