Introdução
Thank you for choosing the STEINEL HS 152 XENO Sensor Halogen Floodlight. This product is designed to provide efficient and reliable outdoor lighting with integrated motion detection for enhanced security and convenience. Please read this manual carefully to ensure proper installation, operation, and maintenance of your floodlight.
Image: STEINEL HS 152 XENO Sensor Halogen Floodlight. This image shows the floodlight from a front-side angle, highlighting its compact design and the integrated motion sensor below the lamp habitação.
Instruções de segurança
WARNING: Risk of electric shock! Installation requires knowledge of electrical systems. Incorrect installation can lead to fire or electric shock. For your safety, always consult a qualified electrician if you have any doubts.
- Disconnect power at the main fuse or circuit breaker before installation or maintenance.
- Garantir o fornecimento voltage matches the floodlight's requirements (230-240V).
- Do not open the product housing unless specified in this manual.
- Não modifique o produto de forma alguma.
- Mantenha as crianças afastadas dos materiais de embalagem.
- The floodlight becomes hot during operation. Avoid touching the lamp or housing immediately after use.
- Garanta o aterramento adequado de acordo com as normas elétricas locais.
- This product is rated IP44 for protection against splashing water. Do not immerse in water.
Conteúdo da embalagem
Verifique se todas as peças estão presentes e sem danos:
- 1x STEINEL HS 152 XENO Sensor Halogen Floodlight (with integrated R7s 150W halogen lamp)
- 1x Set of mounting screws and wall plugs
- 1x Set of cover plates for detection range adjustment
- 1x Manual de Instruções
Instalação
- Preparação: Turn off the power supply at the main circuit breaker. Use a voltage tester to ensure the circuit is de-energized.
- Local de montagem: Choose a suitable mounting location, ideally 1.8m to 2.5m above the ground, where the sensor has an unobstructed view of the desired detection area. Avoid mounting near heat sources or objects that might cause false triggers (e.g., moving branches, busy roads).
- Perfuração: Mark the drilling points using the floodlight's mounting plate as a template. Drill holes and insert wall plugs.
- Fiação: Connect the electrical wires (Live, Neutral, Earth) from your mains supply to the corresponding terminals inside the floodlight's wiring compartment. Ensure all connections are secure.
- Mounting the Floodlight: Secure the floodlight to the wall using the provided screws. Adjust the floodlight head to the desired angle.
- Ligar: Restore power at the main circuit breaker. The floodlight will perform a brief self-test.
Operação
The STEINEL HS 152 XENO floodlight features an integrated passive infrared (PIR) motion sensor. When motion is detected within its adjustable range and the ambient light level falls below the set twilight threshold, the floodlight will automatically switch on for the pre-set duration.
Ajuste do Sensor
The sensor has three main adjustment controls, typically located on the underside of the sensor head:
- Range (Reach): Adjusts the detection distance, up to 12 meters, limitable to approximately 5 meters using the included cover plates. Turn the dial to increase or decrease the range.
- Twilight Threshold (Lux): Sets the ambient light level at which the sensor becomes active. Turn towards the sun symbol for daylight operation (test mode) or towards the moon symbol for activation only in darkness.
- Time Setting (Time): Determines how long the light remains on after motion is detected. Adjust the dial to set the desired duration.
The detection angle is 180° with an opening angle of 90°. Use the provided cover plates to precisely mask out areas you do not wish to be detected, such as public pathways or neighboring properties.
Manutenção
Limpeza
Clean the floodlight and sensor lens regularly with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the surfaces or the sensor lens.
Lamp Substituição
WARNING: Disconnect power before replacing the lamp.
- Ensure the floodlight is cool before handling.
- Abra cuidadosamente o lamp habitação.
- Remove the old R7s halogen lamp.
- Insert a new R7s 150W halogen lamp. Ensure it is correctly seated.
- Feche o lamp housing securely.
- Restaurar energia.
Solução de problemas
| Problema | Possível causa | Solução |
|---|---|---|
| A luz não acende. | Sem fonte de alimentação. Lamp com defeito. Twilight threshold set too high (daylight). O alcance do sensor é muito baixo. | Verifique o disjuntor. Substituir lamp. Adjust twilight setting towards 'moon' symbol. Increase sensor range. |
| A luz permanece acesa continuamente. | Movimento contínuo na área de detecção. Sensor com defeito. | Adjust sensor range or mask detection area. Entre em contato com o suporte ao cliente. |
| A luz acende sem movimento aparente. | False triggers (e.g., heat sources, small animals, moving branches). | Adjust sensor angle, reduce range, or use cover plates to mask problematic areas. |
Especificações
| Marca: | STEINEL |
| Número do modelo: | 632113 |
| Cor: | Preto (Note: Product title indicates 'ws' for white, but specifications list 'Noir' for black.) |
| Recurso especial: | Detector de movimento |
| Material: | Vidro |
| Fonte de energia: | Elétrico com fio |
| Tipo de fonte de luz: | Halogênio |
| Número de fontes de luz: | 1 |
| Volumetage: | 230 Volts |
| O quetage: | 150 Watts |
| Classe de proteção: | IP44 |
| Ângulo de detecção: | 180° (Opening angle 90°) |
| Máx. Faixa de detecção: | 12 meters (adjustable to 5 meters) |
Garantia e Suporte
For warranty information and technical support, please refer to the official STEINEL website or contact your local STEINEL distributor. Keep your purchase receipt as proof of purchase.
STEINEL Contact Information:
- Official STEINEL Website
- Refer to product packaging for specific regional support contacts.
