1. Introdução
This manual provides essential instructions for the proper installation, operation, and maintenance of the Kawasaki Brute Force 650/750 CVT Drive Belt, part number 59011-0003. This genuine Kawasaki OEM part is designed for optimal performance and durability in your ATV's Continuously Variable Transmission (CVT) system. Adhering to these guidelines will help ensure the longevity and efficient operation of your vehicle's drive system.
2. Informações de segurança
Ao trabalhar no seu veículo, priorize sempre a segurança. O não cumprimento das precauções de segurança pode resultar em ferimentos graves ou danos ao veículo.
- Ensure the vehicle is turned off, the engine is cool, and the parking brake is engaged before beginning any work.
- Disconnect the negative battery terminal to prevent accidental starting or electrical shorts.
- Utilize equipamento de proteção individual (EPI) adequado, incluindo óculos de segurança e luvas.
- Trabalhe em uma área bem ventilada.
- If you are unsure about any step, consult a qualified service technician or your vehicle's official service manual.
3. Compatibilidade
This Kawasaki CVT Drive Belt (Part No. 59011-0003) is specifically designed for the following Kawasaki ATV models:
- Kawasaki Brute Force 650
- Kawasaki Brute Force 750
Always verify the part number against your vehicle's specific requirements to ensure correct fitment.
4. Instalação
Replacing the CVT drive belt requires careful attention to detail. Refer to your vehicle's service manual for model-specific torque specifications and detailed disassembly/assembly procedures. The following steps provide a general overview.
4.1. Ferramentas necessárias
- Jogo de soquetes e catraca
- Chave de torque
- Chaves de fenda
- CVT cover gasket (if replacing)
- Belt removal/installation tool (if applicable for your model)
4.2. Preparação
- Park the ATV on a level surface and engage the parking brake.
- Desligue o motor e deixe-o esfriar completamente.
- Locate the CVT cover, typically on the side of the engine.
- Remove any obstacles (e.g., footrests, skid plates) that may block access to the CVT cover.
4.3. Removing the Old Belt
- Carefully remove all bolts securing the CVT cover. Note the location of different length bolts if present.
- Gently pry off the CVT cover. Be cautious of the gasket.
- Inspect the primary and secondary clutches for wear or damage. Clean any dust or debris from the clutch sheaves.
- Compress the secondary clutch (rear clutch) to loosen the belt. This may require a specialized tool or careful manual compression.
- Once slack, remove the old drive belt from both clutches.
Imagem 1: Completa view of the Kawasaki Brute Force CVT Drive Belt (Part No. 59011-0003). This image shows the complete belt, highlighting its continuous loop design and the distinct teeth on its inner surface.
4.4. Installing the New Belt
- Ensure the new Kawasaki 59011-0003 drive belt is clean and free of any contaminants.
- Install the new belt onto the primary (front) clutch first, then compress the secondary clutch to allow the belt to seat properly. Ensure the belt is oriented correctly if it has a directional arrow.
- Rotate the secondary clutch by hand to ensure the belt is fully seated and runs smoothly within the clutch sheaves.
Imagem 2: Angulada view of the Kawasaki Brute Force CVT Drive Belt. This perspective emphasizes the width and thickness of the belt, crucial for its function in the CVT system.
Imagem 3: Close-up view of the teeth on the Kawasaki Brute Force CVT Drive Belt. This detail shows the robust construction and specific tooth pattern designed for efficient power transfer and durability.
4.5. Reassembly and Post-Installation
- Clean the CVT cover and mating surfaces. Install a new gasket if necessary.
- Reinstall the CVT cover, ensuring all bolts are tightened to the manufacturer's specified torque.
- Reattach any removed components (e.g., footrests, skid plates).
- Reconecte o terminal negativo da bateria.
- Start the engine and allow it to idle for a few minutes. Perform a gentle test ride to ensure proper operation of the CVT system.
5. Considerações sobre a operação
After installing a new drive belt, a break-in period is recommended to ensure optimal performance and longevity.
- Período de amaciamento: For the first 30-50 miles (50-80 km), avoid aggressive acceleration, heavy loads, or sustained high speeds. This allows the belt to properly seat into the clutch sheaves.
- Evite a contaminação: Keep the CVT area free from oil, grease, or other liquids, as these can cause belt slippage and premature wear.
- Envolvimento adequado: Always allow the engine to warm up before engaging the transmission, especially in cold weather.
6. Manutenção
Regular inspection and maintenance of your CVT drive belt are crucial for reliable performance.
- Inspeção: Periodically remove the CVT cover and inspect the belt for signs of wear, cracking, fraying, glazing, or missing teeth. Check for any debris inside the CVT housing.
- Limpeza: Use compressed air to clean dust and debris from the CVT housing and clutch components. Avoid using solvents that could damage the belt material.
- Intervalo de substituição: The replacement interval can vary based on riding conditions and usage. Consult your vehicle's service manual for recommended inspection and replacement schedules. Replace the belt immediately if any signs of significant wear or damage are observed.
7. Solução de problemas comuns
If you experience issues with your CVT system, the drive belt may be a contributing factor.
| Sintoma | Possível causa | Ação |
|---|---|---|
| Loss of power / Poor acceleration | Worn or stretched belt, glazed belt, clutch issues | Inspect belt for wear. Replace if necessary. Check clutches for proper operation. |
| Squealing or grinding noise from CVT | Belt slippage, debris in CVT, worn clutch components | Inspect belt for glazing or damage. Clean CVT housing. Check clutch bearings. |
| Belt shredding or breaking prematurely | Overheating, improper installation, clutch misalignment, incorrect belt type | Ensure proper belt installation and break-in. Verify clutch alignment. Confirm correct OEM part number. |
| Vehicle not moving when throttle applied | Broken belt, severe belt slippage, clutch failure | Inspect belt for breakage. If broken, replace. If not, inspect clutches. |
For persistent issues, it is recommended to consult a certified Kawasaki technician.
8. Especificações
- Número da peça: 59011-0003
- Marca: Kawasaki
- Tipo: CVT Drive Belt (Pulley Belt)
- Modelos compatíveis: Kawasaki Brute Force 650, Brute Force 750
- Peso do item: Aproximadamente 12 onças (0.34 kg)
- Fabricante: KAWASAKI
9. Garantia e Suporte
As a genuine Kawasaki OEM part, this drive belt is manufactured to strict quality standards. For specific warranty information, please refer to the official Kawasaki warranty policy or contact an authorized Kawasaki dealer.
For technical assistance or further inquiries, please contact Kawasaki customer support or visit the official Kawasaki website. Always provide the part number (59011-0003) and your vehicle's model information when seeking support.
Recursos on-line: