Introdução
This manual provides detailed instructions for the installation, operation, and maintenance of your Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C. Please read this manual thoroughly before use to ensure proper function and safety.
The Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C, features a clear lens and a robust design for various mounting applications.
Instruções importantes de segurança
- Certifique-se de que todas as conexões elétricas estejam seguras e devidamente isoladas para evitar curtos-circuitos.
- Verify the vehicle's electrical system voltage matches the light's operating voltage (12-60 V CC).
- Disconnect the vehicle's battery before beginning installation to prevent electrical shock.
- Mount the light securely to prevent detachment during vehicle operation.
- Adhere to all local and national regulations regarding the use of emergency warning lights.
Conteúdo da embalagem
- Wolo Apollo 8 GEN 3 LED Emergency Warning Light (Model 3095PPM-C)
- Acessórios de montagem (parafusos, porcas, arruelas)
- Terminais de fio
- Porta-fusível em linha
- Junta de borracha
- Manual de Instruções (este documento)
Configuração e instalação
The Apollo 8 warning light offers two primary mounting options: permanent surface mount or pipe mount.
Permanent Surface Mount
- Choose a flat, stable surface on your vehicle for mounting. Ensure the location provides clear 360° visibility.
- Use the provided rubber gasket as a template to mark the drilling locations for the mounting screws.
- Faça furos piloto nos locais marcados.
- Secure the light base to the surface using the provided mounting hardware (screws, washers, nuts). Ensure a tight fit to prevent vibration.
- Route the power wires to the vehicle's electrical system. Connect the positive wire (typically red) to a switched 12-60V DC power source via the in-line fuse holder. Connect the negative wire (typically black) to a suitable ground point on the vehicle chassis.
- Ensure all wire connections are secure and protected from moisture and abrasion.
Montagem em tubo
- Identify a suitable pipe or pole for mounting. The light is designed to fit standard pipe sizes.
- Use the provided hardware to secure the light base to the pipe.
- Route the power wires and connect them as described in the Permanent Surface Mount section.
Note: Professional installation is recommended if you are unfamiliar with vehicle electrical systems.
Instruções de operação
The Wolo Apollo 8 features eight (8) selectable warning light patterns.
- Once the light is powered on, it will activate in the last selected flash pattern.
- To change the flash pattern, momentarily press the pattern selection button (located on the unit or via a control wire).
- Each press of the button will cycle to the next available warning light pattern.
- Release the button when the desired pattern is displayed. The light will retain this pattern until changed again or power is disconnected.
Manutenção
- Limpeza: Clean the clear polycarbonate lens periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners or solvents that could damage the lens.
- Substituição da lente: The lens is replaceable. If the lens becomes damaged, contact Wolo customer support for replacement parts and instructions.
- Inspeção de fiação: Periodically inspect all wiring and connections for signs of wear, corrosion, or damage. Ensure connections remain secure.
- The GEN 3 LEDs are designed for long life and are maintenance-free, requiring no bulb replacement.
Solução de problemas
| Problema | Possível causa | Solução |
|---|---|---|
| A luz não ilumina | Sem fonte de alimentação | Check power connections, fuse, and vehicle battery. Ensure the light is receiving 12-60V DC. |
| Light flashes erratically | Loose wiring connection or incorrect voltage | Inspect all wiring connections for tightness. Verify input voltage está dentro da faixa de 12-60V CC. |
| Cannot change flash pattern | Faulty pattern selection button or control circuit | Ensure the button is functioning correctly. If the issue persists, contact customer support. |
| Saída de luz reduzida | Lente suja | Clean the lens with a soft cloth and mild soap solution. |
Especificações técnicas
- Modelo: 3095PPM-C
- Fonte de luz: 20 x 1-watt GEN 3 LEDs
- Vol operacionaltage: 12 - 60 Volts CC
- Peak Current Draw: 1.37 Amps
- Light Patterns: 8 selectable patterns
- Material da lente: Polycarbonate Plastic (Clear)
- Material base: Aluminum (Painted Black)
- Opções de montagem: Permanent Surface Mount, Pipe Mount
- Características especiais: Waterproof, Encapsulated Microprocessor, Reduced EMI
- Dimensões: Aproximadamente 6.63 x 6.75 x 6.5 polegadas
- Peso: Aproximadamente 1.85 libras
Garantia e Suporte
Wolo products are designed for durability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official Wolo website.
Suporte ao cliente
For technical assistance, replacement parts, or warranty claims, please contact Wolo customer support.
Wolo Manufacturing Corp.
Parque Deer, NY 11729
