Manual de instruções de montagem do cubo e rolamento de roda MOOG 513346

1. Introdução

This manual provides essential information for the MOOG 513346 Wheel Bearing and Hub Assembly. This component is engineered to deliver reliable performance and facilitate straightforward installation in compatible Ford Mustang vehicles. It features an advanced raceway design for extended service life and coated wheel studs for rust protection.

Figura 1: Frente view do conjunto de cubo e rolamento de roda MOOG 513346.

Figura 2: Traseira view do conjunto de cubo e rolamento de roda MOOG 513346.

2. Compatibilidade

The MOOG 513346 Wheel Bearing and Hub Assembly is compatible with the following Ford Mustang models:

• Ford Mustang 2015-2015
• Ford Mustang 2016-2020
• Ford Mustang 2016-2017
• Ford Mustang 2021-2021

Importante: Antes de comprarasing and installing, verify compatibility with your specific vehicle by checking the manufacturer's fitment guide or consulting a qualified automotive professional.

3. Informações de segurança

Automotive repair can be hazardous. Always prioritize safety. It is recommended that installation be performed by a certified mechanic or an individual with appropriate automotive repair experience.

• Utilize equipamento de proteção individual adequado, incluindo óculos de segurança e luvas.
• Certifique-se de que o veículo esteja apoiado com segurança em cavaletes antes de iniciar qualquer trabalho. Nunca confie apenas no macaco.
• Utilize as ferramentas corretas para cada etapa do processo de instalação.
• Consulte o manual de serviço específico do seu veículo para obter instruções detalhadas e especificações de torque.
• Mantenha crianças e animais de estimação longe da área de trabalho.

4. Componentes incluídos

Cada pacote contém:

• One (1) MOOG 513346 Wheel Bearing and Hub Assembly

Figure 3: Key components of the MOOG Wheel Bearing and Hub Assembly.

5. Diretrizes de instalação

The MOOG 513346 Wheel Bearing and Hub Assembly is designed for fast and hassle-free installation. However, specific steps may vary depending on your vehicle's configuration. Always consult your vehicle's factory service manual for detailed, model-specific instructions.

Etapas gerais de instalação (consulte o manual de serviço do veículo para obter detalhes):

1. Levante e apoie o veículo com segurança. Remova a roda.
2. Remove the brake caliper and rotor.
3. Disconnect any ABS sensor wiring if present.
4. Remove the axle nut. A 35mm socket and a large breaker bar are typically required for this step.
5. Remove the bolts securing the old hub assembly to the steering knuckle.
6. Carefully remove the old hub assembly.
7. Clean the mounting surface on the steering knuckle.
8. Install the new MOOG hub assembly, ensuring proper alignment. The coated wheel studs inhibit rust for easier removal and proper torqueing.
9. Tighten the hub assembly bolts to the manufacturer's specified torque.
10. Install the new axle nut and tighten to the manufacturer's specified torque. A torque wrench capable of 250 ft-lb is often needed for the axle nut.
11. Reconnect the ABS sensor wiring.
12. Reinstall the brake rotor and caliper.
13. Reinstale a roda e abaixe o veículo.

Figure 4: Illustration of wheel installation, highlighting the ease of assembly.

6. Características de Operação

Once installed, the MOOG 513346 Wheel Bearing and Hub Assembly contributes to the safe and smooth operation of your vehicle's wheel system. Its application-specific advanced raceway design is engineered to reduce stress, rotation, and heat on components, thereby extending service life and maintaining optimal performance.

Figure 5: Cross-section illustrating the durable raceway design for extended service life.

7. Manutenção

Wheel bearing and hub assemblies are critical components that require minimal direct maintenance after proper installation. However, regular inspection during tire rotations or brake service is recommended.

• Inspeção: Periodically check for signs of wear, such as excessive play in the wheel, unusual noises, or visible damage to the hub assembly or its seals.
• Lubrificação: This assembly is designed to be maintenance-free with factory-sealed lubrication (grease). No additional lubrication is typically required.
• Proteção contra corrosão: The coated wheel studs are designed to resist corrosion, aiding in easier future removal and proper torqueing.

Figure 6: Coated wheel studs for enhanced corrosion protection.

8. Solução De Problemas

If you suspect an issue with your wheel bearing and hub assembly, observe the following common symptoms:

• Ruído incomum: A humming, grinding, or growling noise that increases with vehicle speed.
• Vibração: Vibrations felt through the steering wheel or floorboard, especially at certain speeds.
• ABS Light: Illumination of the Anti-lock Braking System (ABS) warning light on the dashboard.
• Loose Steering: A feeling of looseness or excessive play in the steering.

If any of these symptoms occur, it is crucial to have your vehicle inspected by a qualified mechanic immediately to prevent further damage or safety risks.

Figure 7: Symptom - Vehicle Noise/Vibration

Figure 8: Symptom - Steering Wheel Vibration

Figure 9: Symptom - ABS Warning Light

9. Especificações

Figure 10: MOOG components undergo rigorous testing for reliability.

10. Informações de garantia

For detailed warranty information regarding the MOOG 513346 Wheel Bearing and Hub Assembly, please refer to the official MOOG website or contact your point of purchase. Warranty terms and conditions may vary.

11. Suporte

If you require technical assistance, have questions about installation, or need further support, please contact MOOG customer service or consult a certified automotive technician.

Você pode encontrar mais informações e detalhes de contato no site oficial. MOOG Store.