Introdução
This manual provides detailed instructions for the installation, operation, and maintenance of your Feit Electric Digital Slide Dimmer. This product is designed for use with LED lighting and is available in a 2-pack. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Informações importantes de segurança
AVISO: To avoid fire, shock, or death; turn off power at circuit breaker or fuse box and test that power is off before wiring! This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician perform this installation.
- Do not use with standard incandescent bulbs unless specified as dimmable.
- Ensure the dimmer's wattage rating (600 watts) is not exceeded.
- Somente para uso interno.
- Always use appropriate safety gear when working with electrical components.
Conteúdo da embalagem
Your Feit Electric Digital Slide Dimmer 2-Pack includes the following items:
- 2 x Feit Electric Digital Slide Dimmers
- 2 x Decorative Wall Plates
- Parafusos de montagem
- Conectores de fio
- Manual de Instruções (este documento)
Image: Front packaging of the Feit Electric Digital Slide Dimmer 2-pack, highlighting the product and its main features like On/Off Switch, Slide Dimmer, Dimming Indicator, Fine Tune Button, and included Decorative Wall Plates.
Image: Back packaging of the Feit Electric Digital Slide Dimmer 2-pack, displaying the internal wiring components, product specifications, and manufacturer information.
Guia de instalação
Antes de começar:
- Turn OFF power at the circuit breaker or fuse box.
- Ensure the existing switch box is clean and free of debris.
- Identify your wiring configuration (single-pole or 3-way).
Wiring Instructions (General):
- Remova cuidadosamente o interruptor existente da caixa de parede.
- Disconnect the wires from the old switch, noting their connections.
- Connect the wires from the wall box to the new Feit Electric dimmer using the provided wire connectors. Refer to the specific wiring diagrams for single-pole or 3-way installations.
- For single-pole installations, connect the hot wire to the dimmer's black wire and the load wire to the dimmer's red wire. Connect the ground wire to the dimmer's green wire.
- For 3-way installations, identify the common wire (usually black or marked) and connect it to the dimmer's black wire. Connect the two traveler wires to the dimmer's red and red/white striped wires. Connect the ground wire to the dimmer's green wire.
- Carefully push the wired dimmer into the wall box.
- Secure the dimmer to the wall box with the mounting screws.
- Fixe a placa decorativa na parede.
- Restaure a energia no disjuntor.
Fine Tune Adjustment:
The dimmer includes a fine tune button to adjust the low-end dimming range for optimal performance with your specific LED bulbs and to eliminate flickering. Use a small screwdriver to turn the adjustment screw located on the dimmer face (often behind the wall plate or a small access panel) until the desired minimum brightness is achieved without flickering.
Operação
Ligar/Desligar:
Press the bottom of the slide dimmer to turn the lights ON or OFF. The dimmer will return to the last set brightness level when turned back on.
Escurecimento:
Slide the control lever up to increase brightness and down to decrease brightness. The dimming indicator will show the current light level.
Manutenção
- Para limpar o dimmer, limpe com um pano macio e seco.amp pano. Não use produtos de limpeza abrasivos ou solventes.
- Ensure power is OFF at the circuit breaker before cleaning.
- No user-serviceable parts inside. Do not attempt to disassemble the dimmer.
Solução de problemas
| Problema | Possível causa | Solução |
|---|---|---|
| As luzes não acendem. | No power to the dimmer; incorrect wiring; bulb(s) burned out. | Check circuit breaker; verify wiring connections; replace bulb(s). |
| Lights flicker at low dimming levels. | Low-end trim setting needs adjustment; incompatible LED bulbs. | Adjust the fine tune button on the dimmer; ensure LED bulbs are dimmable and compatible with the dimmer. |
| O dimmer está quente ao toque. | Normal operation; dimmer is dissipating heat. | This is normal. If it's excessively hot or smells, turn off power and consult an electrician. |
| Lights do not dim smoothly. | Incompatible LED bulbs; fine tune adjustment needed. | Ensure bulbs are designed for smooth dimming; adjust the fine tune button. |
Especificações
- Marca: Feit Elétrico
- Número do modelo: BHBUSAZIN028171
- Modo de operação: Off, Slide Dimmer
- Tipo de contato: Normalmente aberto
- Tipo de conector: Parafuso
- Terminal: Parafuso
- Tipo de Circuito: 4-way (can be used in single-pole or 3-way applications)
- Tipo de atuador: Botão de pressão
- Material de contato: Cobre, latão, prata
- Número de posições: 1
- Especificação atendida: CE
- Método de controle: Tocar
- Protocolo de conectividade: Wi-fi (Note: This specification may refer to potential smart home integration capabilities not explicitly detailed for this specific model, or a data discrepancy.)
- O quetage: 600 watts (Max Incandescent), 150 watts (Max Dimmable LED)
- Contagem de unidades: 2.0 contagem
- Peso do item: 12.3 onças
- Dimensões da embalagem: 10.47 x 8.9 x 1.93 polegadas
- Código UPC: 017801722000
Garantia e Suporte
Feit Electric products are manufactured to the highest quality standards. For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official Feit Electric website. Guarde o recibo de compra para reclamações de garantia.
Para mais informações, visite o Loja Feit Electric na Amazon.
