Manual de instruções do aquecedor de parede com ventilador Stelpro pulsair RWF0502W

Instruções importantes de segurança

Leia todas as instruções antes de instalar ou usar este aquecedor. O não cumprimento destas instruções pode resultar em incêndio, choque elétrico, ferimentos graves ou morte.

• Conexão elétrica: This heater operates on 240 Volts. All wiring must be performed by a qualified electrician and comply with national and local electrical codes.
• Aterramento: Este aquecedor deve ser aterrado.
• Localização: Do not install the heater near flammable materials, in areas where gasoline, paint, or other flammable liquids are stored, or where explosive dust is present. Maintain minimum clearances from walls and other objects as specified in the installation section.
• Supervisão: Close supervision is necessary when any heater is used by or near children or invalids, and whenever the heater is left operating and unattended.
• Superaquecimento: To avoid overheating, do not cover the heater. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
• Manutenção: Disconnect power at the main service panel before performing any maintenance or cleaning.
• Termostato: A separate thermostat is required for operation and is sold separately. Ensure the thermostat is compatible with a fan-forced heater.

Produto acimaview

The Stelpro pulsair RWF0502W is a 240V wall-mounted fan heater designed for supplemental heating in various rooms such as bedrooms, home offices, and living rooms. It utilizes both convection and forced air heating methods to efficiently distribute warmth.

Frente view of the Stelpro pulsair RWF0502W wall fan heater, showing the fan grille and lower air outlet.

Diagram showing the dimensions of the Stelpro pulsair RWF0502W wall fan heater: 17 1/8 inches (435 mm) height, 8 11/16 inches (220 mm) width, and 3 3/16 inches (80 mm) depth.

Instalação

Lista de verificação de pré-instalação:

• Ensure power is disconnected at the main circuit breaker.
• Verifique se o volume de fornecimentotage matches the heater's rating (240V).
• Confirm you have a compatible wall thermostat (sold separately).
• Gather necessary tools: screwdriver, wire strippers, drill, level, measuring tape.

Opções de montagem:

The RWF0502W heater can be either surface-mounted directly to the wall or recessed into the wall for a flush finish. Ensure adequate clearance from floors, ceilings, and adjacent walls as per local codes and manufacturer recommendations.

The Stelpro pulsair RWF0502W wall fan heater installed in a modern entryway, positioned below a plant and mirror.

The Stelpro pulsair RWF0502W wall fan heater installed on a blue wall in an entryway, with coats and shoes nearby.

Conexão elétrica:

This heater requires a 240V hardwired connection. Follow the wiring diagram provided and ensure all connections are secure and properly insulated. Connect the heater to a dedicated circuit protected by the appropriate circuit breaker.

Diagram illustrating the 240V hardwired connection for the Stelpro pulsair RWF0502W wall fan heater, showing wires connecting within a junction box.

1. Desligue a energia no painel elétrico principal.
2. Remove the front grille of the heater to access the wiring compartment.
3. Connect the supply wires to the heater's terminals according to the wiring diagram. Ensure proper grounding.
4. Secure all connections with wire nuts and ensure no bare wires are exposed.
5. Reinstale a grade dianteira.
6. Install the external wall thermostat according to its manufacturer's instructions.

Operação

The Stelpro pulsair RWF0502W heater is controlled by an external wall thermostat (not included). Once installed and wired correctly, follow these steps:

1. Ligar: Restore power to the heater circuit at the main electrical panel.
2. Configuração do termostato: Adjust the external thermostat to your desired temperature. The heater will activate when the room temperature falls below the set point.
3. Operação inicial: During the first few minutes of operation, the heater may emit a slight odor due to the burning off of manufacturing residues. This is normal and will dissipate quickly.
4. Faixa de temperatura: The heater is designed to operate within a temperature range of 5°C (41°F) to 30°C (86°F).

For optimal performance, avoid placing furniture or other obstructions directly in front of the heater's air outlets.

Manutenção

Regular maintenance ensures efficient and safe operation of your Stelpro pulsair heater. Always disconnect power at the main circuit breaker before performing any maintenance.

• Limpeza:
  • Limpe a parte externa do aquecedor com um pano macio e seco.amp pano. Não use produtos de limpeza abrasivos ou solventes.
  • Periodically vacuum the air intake and outlet grilles to remove dust and lint buildup.
• Inspeção: Annually inspect the heater for any signs of damage, loose connections, or unusual wear. If any issues are found, contact a qualified electrician for repair.
• Sem lubrificação: O motor possui lubrificação permanente e não requer lubrificação adicional.

Solução de problemas

If your Stelpro pulsair heater is not operating correctly, consult the following table before contacting customer support.

Especificações

Garantia

Stelpro products are manufactured to high standards and are covered by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Stelpro website. Guarde o comprovante de compra para solicitações de garantia.

Suporte ao cliente

For technical assistance, replacement parts, or further inquiries, please contact Stelpro customer service. Contact information can typically be found on the product packaging, the official Stelpro website, or by referring to the documentation included with your purchase.

Note: Always provide your product model number (RWF0502W) when contacting support.