Manual do Usuário do Sensor de Porta e Janela PGST PB-68

Introdução

The PGST PB-68 Door and Window Sensor is a crucial component of your PGST Home Security System, designed to detect unauthorized entry through doors and windows. This sensor operates by detecting the separation of its two main parts, triggering an alarm signal to your connected PGST alarm host and sending notifications to your smartphone. It provides real-time monitoring and enhances the security of your home or property.

Importante: This sensor requires a PGST alarm host to function correctly and is compatible only with the PGST home security system.

Conteúdo da embalagem

1 x PGST PB-68 Door and Window Sensor (main unit and magnetic contact)
1 x Lithium Ion Battery (pre-installed)
1 x Double-sided Adhesive Tape for installation

Configurar

Requisitos de instalação

A functional PGST alarm host (required for operation).
A clean, dry surface for mounting the sensor.

Etapas de instalação

Prepare a superfície: Clean the desired mounting area on your door or window frame and the corresponding moving part (door/window) to ensure proper adhesion.
Aplique fita adesiva: Apply the provided double-sided adhesive tape to the back of both the main sensor unit and the magnetic contact.
Monte a unidade principal: Mount the larger sensor unit onto the fixed frame of the door or window.
Mount the Magnetic Contact: Mount the smaller magnetic contact onto the moving part of the door or window (the door itself or the window sash).
Alinhar componentes: Ensure that the main sensor unit and the magnetic contact are aligned horizontally and are less than 10 mm (approximately 0.4 inches) apart when the door or window is closed. Proper alignment is critical for correct operation.
Instalação de teste: Open and close the door or window several times to verify that the sensor triggers and resets correctly. Confirm that your PGST alarm host registers the sensor's status changes.

PGST PB-68 Door and Window Sensor components, showing the main sensor unit and the magnetic contact. — This image displays the two main components of the PGST PB-68 Door and Window Sensor: the larger sensor unit and the smaller magnetic contact. These two parts are designed to be mounted adjacent to each other on a door or window frame, with a small gap between them when the door/window is closed.

Instruções de operação

Funcionalidade

Detecção: When the door or window to which the sensor is attached is opened, the main sensor unit and the magnetic contact separate. This separation triggers the sensor.
Disparador de alarme: Upon being triggered, the sensor sends a signal to your connected PGST alarm host. The alarm host will then activate its siren (if armed) and initiate any programmed actions, such as sending notifications.
Monitoramento em tempo real: Through the PGST application on your smartphone, you can monitor the real-time status of your doors and windows (open or closed) 24 hours a day, 7 days a week. You will receive alarm signals on your mobile phone within seconds of a trigger event.

Pairing with PGST Alarm System

Refer to your PGST alarm host's user manual for specific instructions on how to add new sensors to the system. Generally, this involves putting the alarm host into pairing mode and then triggering the sensor (e.g., by separating its two parts) to register it with the system. The process is typically managed through the PGST mobile application.

Manutenção

Substituição da bateria

The PGST PB-68 sensor comes with a pre-installed Lithium Ion battery. When the battery level is low, your PGST alarm host or mobile application will typically notify you. To replace the battery:

Carefully detach the main sensor unit from its mounting surface.
Open the battery compartment (refer to the sensor's casing for specific opening mechanism, usually a small latch or screw).
Remove the old Lithium Ion battery.
Insert a new 3.7V Lithium Ion battery, ensuring correct polarity.
Feche o compartimento da bateria e remonte o sensor.
Test the sensor to ensure it is functioning correctly with the alarm system.

Limpeza

Wipe the sensor's exterior with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the device.

Solução de problemas

Problema	Possível causa	Solução
Sensor not triggering alarm.	Incorrect alignment of sensor and magnet. Sensor not paired with alarm host. Bateria fraca ou descarregada. Alarm system not armed.	Ensure the gap between the sensor and magnet is less than 10 mm when closed. Refer to your alarm host manual to pair the sensor. Substitua a bateria. Arm your PGST alarm system.
No notifications on smartphone.	Sensor not triggering. Smartphone app not configured for notifications. Internet connection issues with alarm host or smartphone.	Troubleshoot sensor triggering (see above). Check app settings for notification permissions and preferences. Verify internet connectivity for both your alarm host and smartphone.
Sensor frequently triggers falsely.	Sensor and magnet too far apart or loose. Vibrations or movement causing slight separation.	Re-align and re-secure the sensor and magnet, ensuring a firm attachment. Consider a more stable mounting location if possible.

Especificações

Número do modelo	PB-68
Sensor Technology	Sensor de contato
Fonte de energia	Alimentado por bateria
Tipo de Bateria	1 x Íon de Lítio (incluída)
Volumetage	3.7 Volts (CC)
Material	Plástico
Método de instalação	Autoadesivo
Tipo de montagem	Saliente
Dimensões do produto	2.95 x 1.96 x 2.16 polegadas
Peso do item	1.44 onças
Dispositivos compatíveis	PGST Home Security System, Smartphone (via app)

Garantia e Suporte

For warranty information, technical support, or further assistance with your PGST PB-68 Door and Window Sensor, please refer to the documentation provided with your PGST alarm host or visit the official PGST website. PGST is committed to customer experience and continuously improving its products and services.

Você também pode encontrar mais informações e entrar em contato com o suporte através do PGST Store on Amazon.