roborock Soft Roller Brush Instruction Manual

1. Produto acabadoview

This manual provides instructions for the roborock Soft Roller Brush, a replacement accessory designed for various roborock F25 series cordless wet dry vacuum cleaners.

Modelos compatíveis:

• roborock F25
• roborock F25 GT
• roborock F25 LT
• roborock F25 RT
• roborock F25 ACE
• roborock F25 ALT
• roborock F25 ACE Combo
• roborock F25 Combo

The roller brush is constructed from dual microfiber and nylons, designed to effectively capture food, hair, dirt, dust, pet dander, and other small particles. It is suitable for use on area rugs and sealed hard floors, including hardwood, tile, marble, laminate, and linoleum floors.

Image 1.1: The roborock Soft Roller Brush is compatible with the F25 Series Wet Dry Vacuum Cleaner.

Image 1.2: The vacuum cleaner with the soft roller brush is effective for homes with pets.

Image 1.3: The soft roller brush is designed to handle various types of spills and messes.

2. Instalação

2.1 Instalação da Alça

1. Align the handle with the main body of the vacuum cleaner.
2. Push the handle firmly into the designated slot until it clicks into place.
3. To remove the handle, press the release button located on the back of the main body and pull the handle upwards.

2.2 Roller Brush Installation

1. Ensure the vacuum cleaner is powered off and disconnected from the charging dock.
2. Open the roller brush cover located at the bottom of the vacuum head.
3. Align the new soft roller brush with the slots in the vacuum head.
4. Gently push the roller brush into place until it is securely seated.
5. Close the roller brush cover, ensuring it clicks firmly into position.

Image 2.1: Step-by-step visual guide for installing the handle and roller brush.

3. Operação

3.1 Ligar/Desligar e Seleção de Modo

• Pressione o botão liga/desliga na alça para ligar ou desligar o aspirador de pó.
• Use the mode selection button to switch between different cleaning modes (e.g., Normal, Eco).

3.2 Abastecendo o reservatório de água limpa

1. Locate the clean water tank, typically positioned on the main body of the vacuum cleaner.
2. Open the tank cap and fill with clean water. You may add a small amount of roborock floor cleaning solution if desired.
3. Close the tank cap securely before use.

3.3 Esvaziamento do tanque de água suja

1. After cleaning, detach the dirty water tank from the main body.
2. Abra cuidadosamente o tanque e descarte a água suja.
3. Enxágue bem o tanque com água limpa e deixe-o secar ao ar antes de reinstalá-lo.

3.4 Função de autolimpeza

The vacuum cleaner features a self-cleaning function to maintain the roller brush. To initiate self-cleaning:

1. Coloque o aspirador de pó na base de carregamento.
2. Ensure the clean water tank has sufficient water and the dirty water tank is empty.
3. Press the dedicated self-cleaning button (refer to your vacuum cleaner's main manual for exact button location).
4. The vacuum will automatically clean the roller brush and dry it. Voice prompts will guide you through the process.

3.5 Lay-Flat Cleaning

The roborock F25 series vacuum cleaners are designed with a lay-flat feature, allowing the main body to recline almost parallel to the floor. This enables cleaning under low-clearance furniture such as sofas and beds, reaching areas that are typically difficult to access.

4. Manutenção

4.1 Limpeza da escova rotativa

Regular cleaning of the roller brush is essential for optimal performance. The brush is reusable and washable.

• After each use, or as needed, remove the roller brush from the vacuum head.
• Rinse the brush under running water to remove any trapped debris, hair, or dirt.
• Allow the roller brush to air dry completely before reinstallation to prevent odors and mildew.

Image 4.1: The soft roller brush is reusable and washable for easy maintenance.

4.2 Limpando o Filtro

The filter in the dirty water tank should also be cleaned regularly to maintain suction power and prevent blockages.

• Retire o filtro do reservatório de água suja.
• Tap off any loose debris and rinse the filter under running water.
• Ensure the filter is completely dry before placing it back into the tank.

4.3 Cronograma de Substituição

For optimal performance and to extend the lifespan of your vacuum cleaner, it is recommended to replace the roller brush every 6 months.

5. Solução De Problemas

If you encounter issues with your roborock Soft Roller Brush or vacuum cleaner, consider the following:

• Bateria fraca: If the vacuum announces "Low Battery," place it on the charging dock immediately.
• Self-Cleaning Not Starting: Ensure the vacuum is correctly placed on the charging dock, the clean water tank is filled, and the dirty water tank is empty.
• Desempenho de limpeza reduzido: Check if the roller brush is clean and free of obstructions. Ensure the filter is clean and properly installed.
• Roller Brush Not Spinning: Verify that the roller brush is correctly installed and not obstructed by debris.
• Ruídos incomuns: Inspect the roller brush and vacuum head for any foreign objects that might be causing the noise.

For persistent issues, refer to the main vacuum cleaner manual or contact roborock customer support.

6. Especificações

7. Garantia e Suporte

For warranty information, please refer to the documentation included with your roborock F25 series vacuum cleaner. To ensure product longevity and optimal performance, it is recommended to purchase replacement parts, such as this Soft Roller Brush, directly from the official roborock store or authorized retailers.

For further assistance or support, please visit the official roborock website ou entre em contato com o departamento de atendimento ao cliente.