INTERRA iX7 Touch Panel Instruction Manual

INTERRA iX7 Touch Panel

Especificações

• Código do produto: ITR165-X0X4
• Fonte de energia: 12-30 VDC or PoE+
• Consumo Nominal de Corrente: 350 mA @12 VDC
• Consumo máximo de corrente: 640 mA @12 VDC
• Communication Current (from KNX Bus): 5 mA
• Consumo Nominal de Energia: 4.2 W a 12 VCC
• Máx. Consumo de energia: 7.7 W a 12 VCC
• CPU: ARM Cortex-A53 de quatro núcleos
• Memória: 2 GB DDR3
• Armazenar: 8 GB EMMC
• SO: Interra Operation System based on AOSP 7.1
• Tipo de proteção: IP20
• USB: 2 x USB2.0
• KNX: 1 x KNX Connector
• Periféricos: Temp/Hum Sensor, MEMS Microphone
• Botão: Botão de reinicialização
• Rede: 100Mbps Ethernet
• RTC: Real Time Clock up to 5 days
• GPIO: 6 Digital Dry Contact Inputs (the Sixth input supports Digital/Analog Mode), 6 Relay Outputs
• Faixa de temperatura:
  • Operação: 0°C a 45°C
  • Armazenamento: -15 ° C a 70 ° C
• Dimensões:
  • Panel: 125 x 210 x 54.15 mm (W x H x D)
  • Mounting Box: 116 x 201 x 65 mm (W x H x D)
• Configuração: With Interra Configurator Software

DESCRIÇÃO

Interra iX7 touch panel is designed to control the entire automation system from a single smart point. Interra İX7 can control complex systems such as switches, simple sensors, lighting, camera systems, and alarm systems from a central point. Moreover, iX7 can also control the air conditioning systems with 2 2-point mode by thermostat functionality. Mobile control can be done by downloading InterraX software from online software markets related to IOS or Android-based devices. Also, the configuration software (Interra Configurator) can be downloaded from our weblocal (www.interratechnology.com) for the iX7 touch panel configuration.

MODELS AND VARIATIONS

MAIN FUNCTIONAL CHARACTERISTICS

• Automation Control: Control EIO (IO Module controlled over ethernet) and KNX automation systems with the Interra Touch Panel.
• Recurso de temporizador: Schedule operations daily, weekly, monthly, or annually using the panel s timer.
• Controle de segurança: Manage security systems and view cameras via the panel and mobile apps.

CONEXÕES

Volumetage: The panel is powered with 12 12-30 VDC via 2 2-pos red coloured connectors. The connector label shows the correct polarity for cable connections.
KNX: The panel has a blue 2 2-pos connector for the KNX port. The connector label shows the correct polarity for cable connections.
USB: The iX7 features two USB host connectors on the side panel for storage expansion.
Ethernet: The panel includes a standard 10/100Mbps RJ45 Ethernet connector.
E/S: The panel has 6 digital dry contact inputs and 6 relay outputs, Input 6 (the sixth input) input)” can operate in digital or analog mode. A temperature sensor can be connected to input 6. Output relay contacts capable of driving 250VAC 5A resistive loads.

Observação: Input 6 operates in analog or digital mode on products that support analog functionality.

DIMENSÕES

segtage Box:

Dispositivo

CARACTERÍSTICAS GERAIS

MONTAGEM

1. First, the mounting box must be attached to a suitable place on the wall. The long side of the mounting box should be placed at a right angle to the ground.
2. Then, iX7 is attached to the mounting box as shown in the left figure, and the mounting process is completed.

INSTRUÇÕES DE SEGURANÇA

• O dispositivo só pode ser instalado e colocado em operação por um eletricista qualificado ou pessoal autorizado.
• For planning and construction of electrical installations, the appropriate specifications, guidelines, and regulations in force in the respective country must be followed.
• Não conecte o volume principaltage (230 VAC) or any other external voltages to any point of the KNX bus.
• Conectando um vol externotage might put the KNX system at risk. Please do not overlook this issue.
• Ensure there is sufficient insulation between the 230 VAC voltage cables and the KNX bus.
• The maximum screwing torque value should be 1.2 Nm during the mounting process of the mount case and touch panel.
• Do not use aerosol sprays, solvents, or abrasives that might damage the device.
• Deve ser fornecida acessibilidade do dispositivo para operação e inspeção visual.